10-18-2015, 07:58 PM
Greetings all,
I was wondering if there were any engineering/physics investigations into the resonant frequencies of the various pyramids and their chambers.
(Moderators: I was unsure where to post this thread. Please feel free to move it to a more appropriate sub-forum.)
It would provide strong confirmation to the brief operational theory outlined in the Law of One. This would be especially so if the chambers resonated at some harmonic, multi-order, or inter-modulation mode.
It would be enhanced even further if the inter-chamber passages had wave-guide mode resonances, relating to these harmonic or heterodyned (Mixed Sum/Difference), frequencies.
At radio frequencies, the resonant frequencies of parabolic and pyramid type radiators while complex,....are clearly defined.
Equilateral Pyramid shapes are still used for impedance transformation in wave-guides, and as actual antennas at high U.H.F up through Microwave frequencies.
They are just much smaller than the Pyramids,.....there is a good chance your Microwave oven has a little copper pyramid, mounted directly on it's Magnetron or Klystron Tube as a Wave-guide. It's usually direct coupled to the Anode and is what focuses the energy into the un-tuned cooking cavity.
However, at audio frequencies, and using air vibration as opposed to electro-magnetic,.....there isn't any formula I can easily work with. There are cone, rectangular, and cylinder formulas.
But,..... I don't see why I can't extrapolate the Radio Formula down to vibratory audio by merely changing the propagation velocity to that of the speed of sound.
(However, I'm not convinced I should disregard the electro-magnetic resonant frequencies, which of course would be very different.)
I have the following questions which could help me in doing this:
1)- Was Ra referring to Electro-Magnetic "vibrational" energy or Aural "vibrational" energy? Am I missing something regarding this in the LOO?
2)- Where is the directional source or locus of the vibrational energy,....from above or below,.....or from a sub-woofer in the back of a Toyota Camry?
2)- Does anyone know were I can find accurate measurements of a particular Pyramid as a whole, it's chambers, and the inter-connecting passages?
3)- Has this already been attempted? If so,...is there anywhere I can find the actual data.
Any help would be greatly appreciated.
I can visualize this from an engineering standpoint very clearly. I just need some numbers to work with.
If I can figure out the Standing Waves,..... then learn where the chambers were located within those Standing Waves,...and can find some correlation between the resonant frequency of each chamber, and which Mode of Standing Wave peaks at the coordinates of each chamber,...it would truly mean something amazing.
It could very well confirm what most of us here believe the purpose of the Pyramids were.
I just can't buy they were merely the equivalent of some ancient ruler's gigantic, post-humus graffiti tag.
I was wondering if there were any engineering/physics investigations into the resonant frequencies of the various pyramids and their chambers.
(Moderators: I was unsure where to post this thread. Please feel free to move it to a more appropriate sub-forum.)
It would provide strong confirmation to the brief operational theory outlined in the Law of One. This would be especially so if the chambers resonated at some harmonic, multi-order, or inter-modulation mode.
It would be enhanced even further if the inter-chamber passages had wave-guide mode resonances, relating to these harmonic or heterodyned (Mixed Sum/Difference), frequencies.
At radio frequencies, the resonant frequencies of parabolic and pyramid type radiators while complex,....are clearly defined.
Equilateral Pyramid shapes are still used for impedance transformation in wave-guides, and as actual antennas at high U.H.F up through Microwave frequencies.
They are just much smaller than the Pyramids,.....there is a good chance your Microwave oven has a little copper pyramid, mounted directly on it's Magnetron or Klystron Tube as a Wave-guide. It's usually direct coupled to the Anode and is what focuses the energy into the un-tuned cooking cavity.
However, at audio frequencies, and using air vibration as opposed to electro-magnetic,.....there isn't any formula I can easily work with. There are cone, rectangular, and cylinder formulas.
But,..... I don't see why I can't extrapolate the Radio Formula down to vibratory audio by merely changing the propagation velocity to that of the speed of sound.
(However, I'm not convinced I should disregard the electro-magnetic resonant frequencies, which of course would be very different.)
I have the following questions which could help me in doing this:
1)- Was Ra referring to Electro-Magnetic "vibrational" energy or Aural "vibrational" energy? Am I missing something regarding this in the LOO?
2)- Where is the directional source or locus of the vibrational energy,....from above or below,.....or from a sub-woofer in the back of a Toyota Camry?
2)- Does anyone know were I can find accurate measurements of a particular Pyramid as a whole, it's chambers, and the inter-connecting passages?
3)- Has this already been attempted? If so,...is there anywhere I can find the actual data.
Any help would be greatly appreciated.
I can visualize this from an engineering standpoint very clearly. I just need some numbers to work with.
If I can figure out the Standing Waves,..... then learn where the chambers were located within those Standing Waves,...and can find some correlation between the resonant frequency of each chamber, and which Mode of Standing Wave peaks at the coordinates of each chamber,...it would truly mean something amazing.
It could very well confirm what most of us here believe the purpose of the Pyramids were.
I just can't buy they were merely the equivalent of some ancient ruler's gigantic, post-humus graffiti tag.